 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Ordering number : EN*A1130 STK672-640A-E Overview Thick-Film Hybrid IC 2-phase Stepping Motor Driver The STK672-640A-E is a hybrid IC for use as a unipolar, 2-phase stepping motor driver with PWM current control. Applications * Office photocopiers, printers, etc. Features * Built-in overcurrent detection function (output current OFF). * Built-in overheat detection function (output current OFF). * If either over-current or overheat detection function is activated, the FAULT signal (active low) is output. * Built-in power on reset function. * The motor speed is controlled by the frequency of an external clock signal. * 2 phase or 1-2 phase excitation switching function. * Using either or both edges of the clock signal switching function. * Phase is maintained even when the excitation mode is switched. * Rotational direction switching function. * Supports schmitt input for 2.5V high level input. * Incorporating a current detection resistor (0.089: resistor tolerance 2%), motor current can be set using two external resistors. * The ENABLE pin can be used to cut output current while maintaining the excitation mode. * With a wide current setting range, power consumption can be reduced during standby. * No motor sound is generated during hold mode due to external excitation current control. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. 71608HKIM No. A1130-1/21 STK672-640A-E Specifications Absolute Maximum Ratings at Tc = 25C Parameter Maximum supply voltage 1 Maximum supply voltage 2 Input voltage Output current 1 Output current 2 Output current 3 Allowable power dissipation 1 Allowable power dissipation 2 Operating substrate temperature Junction temperature Storage temperature Symbol VCC max VDD max VIN max IOP max IOH max IOF max PdMF max PdPK max Tc max Tj max Tstg No signal No signal Logic input pins 10A, 1 pulse (resistance load) VDD=5V, CLOCK200Hz Pin16 output current With an arbitrarily large heat sink. Per MOSFET No heat sink Conditions Ratings 52 -0.3 to +6.0 -0.3 to +6.0 20 4 10 8.3 3.1 105 150 -40 to +125 unit V V V A A mA W W C C C Allowable Operating Ranges at Ta=25C Parameter Operating supply voltage 1 Operating supply voltage 2 Input high voltage Input low voltage Output current 1 Output current 2 Symbol VCC VDD VIH VIL IOH1 IOH2 With signals applied With signals applied Pins 10, 12, 13, 14, 15, 17 Pins 10, 12, 13, 14, 15, 17 Tc=105C, CLOCK200Hz, Continuous operation, duty=100% Tc=80C, CLOCK200Hz, Continuous operation, duty=100%, See the motor current (IOH) derating curve CLOCK frequency Phase driver withstand voltage Recommended operating substrate temperature Recommended Vref range Vref Tc=105C fCL VDSS Tc Minimum pulse width: at least 10s ID=1mA (Tc=25C) No condensation 0 to 50 100min 0 to 105 0.14 to 1.31 kHz V C V 3.3 A Conditions Ratings 10 to 42 55% 2.5 to VDD 0 to 0.8 3.0 unit V V V V A Refer to the graph for each conduction-period tolerance range for the output current and brake current. Electrical Characteristics at Tc=25C, VCC=24V, VDD=5.0V Parameter VDD supply current Output average current FET diode forward voltage Output saturation voltage Input high voltage Input low voltage FAULT low output voltage 5V level FAULT leakage current 5V level input current GND level input current Vref input bias current PWM frequency Overheat detection temperature Symbol ICCO Ioave Vdf Vsat VIH VIL VOLF IILF IILH IILL IIB fc TSD Design guarantee Conditions Pin 9 current CLOCK=GND R/L=1/0.62mH in each phase If=1A (RL=23) RL=23 Pins 10, 12, 13, 14, 15, 17 Pins 10, 12, 13, 14, 15, 17 Pin 16 (IO=5mA) Pin 16=5V Pins 10, 12, 13, 14, 15, 17=5V Pins 10, 12, 13, 14, 15, 17=GND Pin 19=1.0V 29 10 45 144 50 0.25 2.5 0.8 0.5 10 75 10 15 61 0.519 min typ 4.4 0.625 0.83 0.20 max 8 0.731 1.5 0.33 unit mA A V V V V V A A A A kHz C *Ioave values are for when the lead frame of the product is soldered to the mounting substrate. Notes: A fixed-voltage power supply must be used. No. A1130-2/21 STK672-640A-E Package Dimensions unit:mm (typ) 29.2 25.6 (20.47) 2.0 4.5 (12.9) (5.0) (5.0) (R1.7) 11.0 14.5 14.4 7.2 1 19 (3.5) 1.0 (5.6) 18 1.0=18.0 0.52 4.2 0.4 8.2 (20.4) Derating curve of motor current, IOH, vs. STK672-640A-E Operating substrate temperature, Tc 4.5 4.0 3.5 IOH - Tc 200Hz 2-phase excitation Hold mode Motor current, IOH - A 3.0 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 50 60 70 80 90 100 110 ITF02588 Operating Substrate Temperature, Tc- C Notes * The current range given above represents conditions when output voltage is not in the avalanche state. * If the output voltage is in the avalanche state, see the allowable avalanche energy for STK672-6** series hybrid ICs given in a separate document. * The operating substrate temperature, Tc, given above is measured while the motor is operating. * Because Tc varies depending on the ambient temperature, Ta, the value of IOH, and the continuous or intermittent operation of IOH, always verify this value using an actual set. 14.5 No. A1130-3/21 STK672-640A-E Block Diagram N.C 8 VDD=5V 9 Excitation mode selection Phase advance counter Latch Circuit VDD FAO Phase excitation signal generator FAB FBO FBB 7 N.C 4 F1 A 5 F2 AB 3 F3 B 1 F4 BB MODE1 10 N.C 11 MODE2 17 CLOCK 12 CWB 13 RESETB 14 ENABLE 15 Power-on reset Overcurrent detection R1 R2 P.G2 AI 2 P.G1 6 Vref Amplifier VSS 100k VSS VSS FAULT signal (open drain) Overheating detection Latch Circuit Current control chopper circuit Vref/4.9 FAULT 16 BI S.G 18 Vref 19 Sample Application Circuit STK672-640A-E VDD(5V) CLOCK MODE1 MODE2 CWB ENABLE RESETB 14 R01 FAULT Vref 19 R02 18 9 12 10 17 13 15 3 1 B BB + C01 at least 100F 16 2 6 S.G P.G2 P.G1 4 5 A AB VCC 24V 2 phase stepping motor driver R03 P.GND No. A1130-4/21 STK672-640A-E Precautions [GND wiring] * To reduce noise on the 5V system, be sure to place the GND of C01 in the circuit given above as close as possible to Pin 2 and Pin 6 of the hybrid IC. Also, to achieve accurate current settings, be sure to connect Vref GND to Pin 18 (S.G) used to set the current and to the point where P.G1 and P.G2 share a connection. [Input pins] * If VDD is being applied, use care that each input pin does not apply a negative voltage less than -0.3V to S.G, Pin 18, and do not apply a voltage greater than or equal to VDD voltage. * Do not wire by connecting the circuit pattern on the P.C.B side to Pins 7, 8, or 11 on the N.C. shown in the internal block diagram. * Apply 2.5V high level input to pins 10, 12, 13, 14, 15, and 17. * Since the input pins do not have built-in pull-up resistors, when the open-collector type pins 10, 12, 13, 14, 15, and 17 are used as inputs, a 1 to 20k pull-up resistor (to VDD) must be used. At this time, use a device for the open collector driver that has output current specifications that pull the voltage down to less than 0.8V at Low level (less than 0.8V at Low level when IOL=5mA). [Current setting Vref] * Considering the specifications of the Vref input bias current, IIB, a value of 1k or less is recommended for R02. If the motor current is temporarily reduced, the circuit given below (STK672-630A-E: IOH>0.2A, STK672-640A-E: IOH>0.3A) is recommended. 5V R01 Vref R3 R02 R01 Vref R3 5V R02 * Motor current peak value IOH setting IOH 0 IOH=(Vref/4.9) /Rs The value of 4.9 in Equation above represents the Vref voltage as divided by a circuit inside the control IC. Vref=(R02/ (R01+R02)) x5V(or 3.3V) Rs is an internal current detection resistor value of the hybrid IC. Rs=0.141 when using the STK672-630A-E Rs=0.089 when using the STK672-640A-E No. A1130-5/21 STK672-640A-E [Smoke Emission Precuations] If Pin 18 (S.G terminal) is attached to the PCB without using solder, overcurrent may flow into the MOSFET at VCCON (24V ON), causing the STK672-630A-E, STK672-640A-E to emit smoke because 5V circuits cannot be controlled. In addition, as long as one of the output Pins, 1, 3, 4, or 5, is open, inductance energy stored in the motor results in electrical stress on the driver, possibly resulting in the emission of smoke. Input Pin Functions Pin Name CLOCK MODE1 MODE2 CWB RESETB Pin No. 12 10 17 13 14 Motor direction switching System reset Initial state of A and BB phase excitation in the timing charts is set by switching from low to high. ENABLE 15 The A, AB, B, and BB outputs are turned off, and after operation is restored by returning the ENABLE pin to the high level, operation continues with the same excitation timing as before the low-level input. The A, AB, B, and BB outputs are turned off by a lowlevel input. Function Reference clock for motor phase current switching Excitation mode selection Input Conditions When Operating Operates on the rising edge of the signal (MODE2=H) Low: 2-phase excitation High: 1-2 phase excitation High: Rising edge Low: Rising and falling edge Low: CW (forward) High: CCW (reverse) A reset is applied by a low level Output Pin Functions Pin Name FAULT Pin No. 16 Function Monitor pin used when over-current detection or overheat detection function is activated. Input Conditions When Operating Low level is output when detected. Note: See the timing chart for the concrete details on circuit operation. No. A1130-6/21 STK672-640A-E Timing Charts 2-phase excitation VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB 1-2 phase excitation VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB No. A1130-7/21 STK672-640A-E 1-2 phase excitation (CWB) VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB 2 phase excitation Switch to 1-2 phase excitation VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB No. A1130-8/21 STK672-640A-E 1-2 phase excitation (ENABLE) VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB 1-2 phase excitation (Hold operation results during fixed CLOCK) VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE Hold operation FAO FAB FBO FBB No. A1130-9/21 STK672-640A-E 2 phase excitation (MODE 2) VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB 1-2 phase excitation (MODE 2) VDD Power On Reset (or RESETB) MODE1 MODE2 CWB CLOCK ENABLE FAO FAB FBO FBB No. A1130-10/21 STK672-640A-E Usage Notes 1. STK672-630A-E, STK672-640A-E input signal functions and timing [ENABLE, CLOCK and power on reset, RESETB (Input signal timing when power is first applied)] The control IC of the driver is equipped with a power on reset function capable of initializing internal IC operations when power is supplied. A 4V typ setting is used for power on reset. Because the specification for the MOSFET gate voltage is 5V5%, conduction of current to output at the time of power on reset adds electromotive stress to the MOSFET due to lack of gate voltage. To prevent electromotive stress, be sure to set ENABLE=Low while VDD, which is outside the operating supply voltage, is less than 4.75V. In addition, if the RESETB terminal is used to initialize output timing, be sure to allow at least 10s until CLOCK input. 4V typ Control IC power (VDD) rising edge Control IC power on reset 3.8V typ RESETB signal input No time specification ENABLE signal input CLOCK signal input At least 10s At least 10s ENABLE, CLOCK, and RESETB Signals Input Timing [CLOCK (Phase switching clock)] * Input frequency: DC to 50kHz * Minimum pulse width: 10s * MODE2=1(High) Signals are read on the rising edge. * MODE2=0(Low) Signals are read on the rising and falling edges. [CWB (Motor direction setting)] The direction of rotation is switched by setting CWB to 1 (high) or 0 (low). See the timing charts for details on the operation of the outputs. Note: The state of the CWB input must not be changed during the 6.25s period before and after the rising edge of the CLOCK input. [ENABLE (Forcible on/off control of the A, AB, B, and BB outputs, and hybrid IC internal operation)] ENABLE=1: Normal operation ENABLE=0: Outputs A, AB, B, and BB forced to the off state. If, during the state where CLOCK signal input is provided, the ENABLE pin is set to 0 and then is later restored to the 1 state, the IC will resume operation with the excitation timing continued from before the point ENABLE was set to 0. If sudden stop is applied to the CLOCK signal used for motor rotation, the motor axis may advance beyond the theoretical position due to inertia. To stop at the theoretical position, the SLOW DOWN setting for gradually slowing the CLOCK cycle is required. No. A1130-11/21 STK672-640A-E [MODE1 and MODE2 (Excitation mode selection)] MODE1=0: 2-phase excitation MODE2=1: Rising edge of CLOCK MODE1=1: 1-2 phase excitation MODE2=0: Rising and falling edges of CLOCK See the timing charts for details on output operation in these modes. Note: The state of the MODE input must not be changed during the 5s period before and after the rising edge of the CLOCK input. [Configuration of Each Input Pin] 5V 10k 100k VSS All input pins of this driver support schmitt input. Typ specifications at Tc = 25C are given below. Hysteresis voltage is 0.3V (VIHa-VILa). When rising 1.8V typ Input voltage When falling 1.5V typ VIHa VILa Input voltage specifications are as follows. VIH=2.5V min VIL=0.8V max 5V Vref/4.9 - Output pin Pin 16 Amplifier + 100k VSS VSS VSS Input pin Pin 19 The internal impedance, 100k, is designed so that the increase in current is prevented while Pin 19 is open. The recommended Vref voltage is 0.14V or higher because the output offset voltage of Vref/4.9 amplifier cannot be controlled down to 0V No. A1130-12/21 STK672-640A-E 2. Overcurrent Detection and Overheat Detection Functions of the STK672-630A-E and STK672-640A-E Each detection function operates using a latch system and turns output off. Because a RESET signal is required to restore output operations, once the power supply, VDD, is turned off, you must either again apply power on reset with VDDON or apply a RESETB=HighLowHigh signal. [Overcurrent detection] This hybrid IC is equipped with a function for detecting overcurrent that arises when the motor burns out or when there is a short between the motor terminals. Overcurrent detection occurs at 3.5A typ with the STK672-630A-E and at 5.5A typ for the STK672-640A-E. Current when motor terminals are shorted PWM period Set motor current, IOH Over-current detection IOH max MOSFET all OFF No detection interval (5.5s typ) Normal operation 5.5s typ Operation when motor pins are shorted Overcurrent detection begins after an interval of no detection (a dead time of 5.5s typ) during the initial ringing part during PWM operations. The no detection interval is a period of time where overcurrent is not detected even if the current exceeds IOH. [Overheat detection] Rather than directly detecting the temperature of the semiconductor device, overheat detection detects the temperature of the aluminum substrate (144C typ). Within the allowed operating range recommended in the specification manual, if a heat sink attached for the purpose of reducing the operating substrate temperature, Tc, comes loose, the semiconductor can operate without breaking. However, we cannot guarantee operations without breaking in the case of operations other than those recommended, such as operations at a current exceeding IOH max that occurs before overcurrent detection is activated. No. A1130-13/21 STK672-640A-E 3. Calculating STK672-640A-E HIC Internal Power Loss The average internal power loss in each excitation mode of the STK672-640A-E can be calculated from the following formulas. Each excitation mode 2-phase excitation mode 2PdAVex=(Vsat+Vdf) x0.5xCLOCKxIOHxt2+0.5xCLOCKxIOHx (Vsatxt1+Vdfxt3) 1-2 Phase excitation mode 1-2PdAVex=(Vsat+Vdf) x0.25xCLOCKxIOHxt2+0.25xCLOCKxIOHx (Vsatxt1+Vdfxt3) Motor hold mode HoldPdAVex= (Vsat+Vdf) xIOH Vsat: Combined voltage represented by the Ron voltage drop+shunt resistor Vdf: Combined voltage represented by the MOSFET body diode+shunt resistor CLOCK: Input CLOCK (CLOCK pin signal frequency) t1, t2, and t3 represent the waveforms shown in the figure below. t1: Time required for the winding current to reach the set current (IOH) t2: Time in the constant current control (PWM) region t3: Time from end of phase input signal until inverse current regeneration is complete IOH 0A t1 t2 t3 Motor COM Current Waveform Model t1= (-L/(R+0.20)) In (1-((R+0.20)/VCC) xIOH) t3= (-L/R) In ((VCC+0.20)/(IOHxR+VCC+0.20)) VCC: Motor supply voltage (V) L: Motor inductance (H) R: Motor winding resistance () IOH: Motor set output current crest value (A) Relationship of CLOCK, t1, t2, and t3 in each excitation mode 2-phase excitation mode: t2= (2/CLOCK) - (t1+t3) 1-2 phase excitation mode: t2= (3/CLOCK) -t1 For Vsat and Vdf, be sure to substitute values from the graphs of Vsat vs. IOH and Vdf vs. IOH while the set current value is IOH. Then, determine whether a heat sink is required by comparing with the graph of Tc vs. Pd based on the average HIC power loss calculated. When designing a heat sink, refer to the section "Thermal design" found on the next page. The average HIC power loss, PdAV, described above does not have the avalanche's loss. To include the avalanche's loss, be sure to add Equation (2), "STK672-6** Allowable Avalanche Energy Value" to PdAV above. When using this IC without a fin always check for temperature increases in the set, because the HIC substrate temperature, Tc, varies due to effects of convection around the HIC. No. A1130-14/21 STK672-640A-E STK672-640A-E Output saturation voltage, Vsat - Output current, IOH 1.0 Vsat - IOH Output saturation voltage, Vsat - V 0.8 0.6 Tc =1 0 0.5 1.0 1.5 2.0 0.4 0.2 0 2.5 3.0 3.5 4.0 4.5 ITF02589 Output current, IOH - A STK672-640A-E Forward voltage, Vdf -Output current, IOH 1.4 Vdf- IOH 1.2 Forward voltage, Vdf - V 1.0 25C Tc= C 105 0.8 0.6 0.4 0.2 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 ITF02590 Output current, IOH - A Substrate temperature rise, Tc (no heat sink) - Internal average power dissipation, PdAV 80 70 60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 ITF02551 Tc - PdAV Substrate temperature rise, Tc - C Hybrid IC internal average power dissipation, PdAV - W 05 C C 25 No. A1130-15/21 STK672-640A-E 4. STK672-640A-E Allowable Avalanche Energy Value (1) Allowable Range in Avalanche Mode When driving a 2-phase stepping motor with constant current chopping using an STK672-6** Series hybrid IC, the waveforms shown in Figure 1 below result for the output current, ID, and voltage, VDS. VDSS: Voltage during avalanche operations VDS IOH: Motor current peak value IAVL: Current during avalanche operations ID tAVL: Time of avalanche operations ITF02557 Figure 1 Output Current, ID, and Voltage, VDS, Waveforms 1 of the STK672-6** Series when Driving a 2-Phase Stepping Motor with Constant Current Chopping When operations of the MOSFET built into STK672-6** Series ICs is turned off for constant current chopping, the ID signal falls like the waveform shown in the figure above. At this time, the output voltage, VDS, suddenly rises due to electromagnetic induction generated by the motor coil. In the case of voltage that rises suddenly, voltage is restricted by the MOSFET VDSS. Voltage restriction by VDSS results in a MOSFET avalanche. During avalanche operations, ID flows and the instantaneous energy at this time, EAVL1, is represented by Equation (1). EAVL1=VDSSxIAVLx0.5xtAVL ------------------------------------------- (1) VDSS: V units, IAVL: A units, tAVL: sec units The coefficient 0.5 in Equation (1) is a constant required to convert the IAVL triangle wave to a square wave. During STK672-6** Series operations, the waveforms in the figure above repeat due to the constant current chopping operation. The allowable avalanche energy, EAVL, is therefore represented by Equation (2) used to find the average power loss, PAVL, during avalanche mode multiplied by the chopping frequency in Equation (1). PAVL=VDSSxIAVLx0.5xtAVLxfc ------------------------------------------- (2) fc: Hz units (fc is set to the PWM frequency of 50kHz.) For VDSS, IAVL, and tAVL, be sure to actually operate the STK672-6** Series and substitute values when operations are observed using an oscilloscope. Ex. If VDSS=110V, IAVL=1A, tAVL=0.2s when using a STK672-640A-E driver, the result is: PAVL=110x1x0.5x0.2x10-6x50x103=0.55W VDSS=110V is a value actually measured using an oscilloscope. The allowable loss range for the allowable avalanche energy value, PAVL, is shown in the graph in Figure 3. When examining the avalanche energy, be sure to actually drive a motor and observe the ID, VDSS, and tAVL waveforms during operation, and then check that the result of calculating Equation (2) falls within the allowable range for avalanche operations. No. A1130-16/21 STK672-640A-E (2) ID and VDSS Operating Waveforms in Non-avalanche Mode Although the waveforms during avalanche mode are given in Figure 1, sometimes an avalanche does not result during actual operations. Factors causing avalanche are listed below. * Poor coupling of the motor's phase coils (electromagnetic coupling of A phase and AB phase, B phase and BB phase). * Increase in the lead inductance of the harness caused by the circuit pattern of the P.C. board and motor. * Increases in VDSS, tAVL, and IAVL in Figure 1 due to an increase in the supply voltage from 24V to 36V. If the factors above are negligible, the waveforms shown in Figure 1 become waveforms without avalanche as shown in Figure 2. Under operations shown in Figure 2, avalanche does not occur and there is no need to consider the allowable loss range of PAVL shown in Figure 3. VDS IOH: Motor current peak value ID ITF02558 Figure 2 Output Current, ID, and Voltage, VDS, Waveforms 2 of the STK672-6** Series when Driving a 2-Phase Stepping Motor with Constant Current Chopping Figure 3 Allowable Loss Range, PAVL-IOH During STK672-640A-E Avalanche Operations Average power loss in the avalanche state, PAVL- W 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 ITF02591 PAVL - IOH Tc= 80 C 105 C Motor phase current, IOH - A Note: The operating conditions given above represent a loss when driving a 2-phase stepping motor with constant current chopping. Because it is possible to apply 3W or more at IOH=0A, be sure to avoid using the MOSFET body diode that is used to drive the motor as a zener diode. No. A1130-17/21 STK672-640A-E 5. Thermal design [Operating range in which a heat sink is not used] Use of a heat sink to lower the operating substrate temperature of the HIC (Hybrid IC) is effective in increasing the quality of the HIC. The size of heat sink for the HIC varies depending on the magnitude of the average power loss, PdAV, within the HIC. The value of PdAV increases as the output current increases. To calculate PdAV, refer to "Calculating Internal HIC Loss for the STK672-630A-E, STK672-640A-E" in the specification document. Calculate the internal HIC loss, PdAV, assuming repeat operation such as shown in Figure 1 below, since conduction during motor rotation and off time both exist during actual motor operations, IO1 Motor phase current (sink side) IO2 0A -IO1 T1 T3 T2 T0 Figure 1 Motor Current Timing T1: Motor rotation operation time T2: Motor hold operation time T3: Motor current off time T2 may be reduced, depending on the application. T0: Single repeated motor operating cycle IO1 and IO2: Motor current peak values Due to the structure of motor windings, the phase current is a positive and negative current with a pulse form. Note that figure 1 presents the concepts here, and that the on/off duty of the actual signals will differ. The hybrid IC internal average power dissipation PdAV can be calculated from the following formula. PdAV= (T1xP1+T2xP2+T3x0) /TO ---------------------------- (I) (Here, P1 is the PdAV for IO1 and P2 is the PdAV for IO2) If the value calculated using Equation (I) is 1.5W or less, and the ambient temperature, Ta, is 60C or less, there is no need to attach a heat sink. Refer to Figure 2 for operating substrate temperature data when no heat sink is used. [Operating range in which a heat sink is used] Although a heat sink is attached to lower Tc if PdAV increases, the resulting size can be found using the value of c-a in Equation (II) below and the graph depicted in Figure 3. c-a= (Tc max-Ta) /PdAV ---------------------------- (II) Tc max: Maximum operating substrate temperature =105C Ta: HIC ambient temperature Although a heat sink can be designed based on equations (I) and (II) above, be sure to mount the HIC in a set and confirm that the substrate temperature, Tc, is 105C or less. The average HIC power loss, PdAV, described above represents the power loss when there is no avalanche operation. To add the loss during avalanche operations, be sure to add Equation (2), "Allowable STK672-6** Avalanche Energy Value", to PdAV. No. A1130-18/21 STK672-640A-E Figure 2 Substrate temperature rise, Tc (no heat sink) - Internal average power dissipation, PdAV 80 70 60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 ITF02553 Tc - PdAV Substrate temperature rise, Tc - C Hybrid IC internal average power dissipation, PdAV - W Figure 3 Heat sink area (Board thickness: 2mm) - c-a 100 c-a - S Heat sink thermal resistance, c-a - C/W 7 5 3 2 10 7 5 3 2 Wit Wi t ha o su rfac e fi nish flat blac k su rfac e fi nish hn 1.0 10 2 3 5 7 100 2 3 5 7 1000 ITF02554 Heat sink area, S - cm2 6. Mitigated Curve of Package Power Loss, PdPK, vs. Ambient Temperature, Ta Package power loss, PdPK, refers to the average internal power loss, PdAV, allowable without a heat sink. The figure below represents the allowable power loss, PdPK, vs. fluctuations in the ambient temperature, Ta. Power loss of up to 3.1W is allowable at Ta=25C, and of up to 1.75W at Ta=60C. Allowable power dissipation, PdPK(no heat sink) - Ambient temperature, Ta 3.5 PdPK - Ta Allowable power dissipation, PdPK - W 3.0 2.5 2.0 1.5 1.0 0.5 0 0 20 40 60 80 100 120 ITF02511 Ambient temperature,Ta - C No. A1130-19/21 STK672-640A-E 7. Example of Stepping Motor Driver Output Current Path (1-2 phase excitation) 2-phase stepping motor IOA IOAB N.C N.C A AB B BB VDD=5V MODE1 N.C MODE2 CLOCK CWB Excitatin mode setting Phase advnce counter Power on reset FAULT signal (Opendrain) Over heat detection S.G Vref Latch VDD FAO Phase excitation signal generation Over current detection FAB FBO FBB F1 F2 F3 F4 VCC 24V Latch RESETB ENABLE FAULT + C02 at least 100F P.G2 AI BI P.G1 Chopper circuit Vref/4.9 P.GND Vref VSS Amp VSS 100k V CLOCK Phase A output current IOA PWM operations When PWM operations of IOA are OFF, for IOAB, negative current flows through the parasitic diode, F2. Phase AB output current IOAB When PWM operations of IOAB are OFF, for IOA, negative current flows through the parasitic diode, F1. No. A1130-20/21 STK672-640A-E SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2008. Specifications and information herein are subject to change without notice. PS No. A1130-21/21 |
Price & Availability of STK672-640A-E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |